Small stone powder making machine
is one of the indispensable equipment for processing stone powder. It can be adapted to the crushing and grinding of various ore materials. It is widely used in barite, calcite, marble, limestone, glass, insulation materials, etc. Mohs hardness is not greater than 9.3 level, high-fine powder processing of materials with humidity below 6%.
Introduction of several commonly used small stone powder making machines
The particle size of the small stone powder making machine is between 80 mesh and 800 mesh, which can meet the needs of different users. There are many types of mills used to grind stones into powder. Commonly used are Raymond mills, HGM German ultra-fine mills, and high-strength mills. Here are a few small stone powder making machines.
1. YGM Raymond mill for stone powder making:
8-78t/h, feed size ≤25mm, finished product size 80-325 mesh, machine transmission is stable, reliable operation, through sieve rate as high as 99%, finished product fineness is uniform, less impurities , The wearing parts are made of high manganese steel with long service life.
YGM Raymond mill for stone powder making
2. MTM high-pressure roller mill for stone powder making:
1-20t/hour, feed size ≤15mm, finished product size 80-425 mesh, small size of the equipment, PLC electrical automation control, effectively reducing the failure rate of the equipment, grinding rollers, grinding rings Strong and wear-resistant, long service life, large output, and output increased by 10-20%; simple structure and convenient operation.
MTM high-pressure roller mill for stone powder making
0.5-45t/hour, feed size ≤20mm, finished product size 400-2500 mesh, it is a new generation of powder made by absorbing German advanced technology and the company's more than 20 years of milling technology experience. This mill has low investment, high profitability, strong rolling pressure, good sealing performance, environmental protection and high production.
HGM ultra-fine mill for stone powder making
4. CLUM ultra-fine vertical mill:
3-20t/hour, feed size ≤10mm, finished product size 400-3000 mesh. The powder produced by this equipment has high fineness and good sphericity, which is suitable for the manufacture of high-end superfine powder.
CLUM ultra-fine vertical mill for stone powder making
Performance advantages of small stone powder making machine
The performance of the small stone powder making machine equipment is good, and it has obvious advantages in production.
1. Strong rolling pressure:
The grinding force of the grinding roller on the material is greatly improved under the action of the high-pressure spring. Compared with other mills of the same type, the grinding capacity of this equipment is stronger.
2. Large production capacity:
The production capacity of the small stone powder making machine has been improved, and the production capacity has been improved a lot by adopting new technologies. The small ore mill has lower energy consumption and greater benefits.
3. Green and environmental protection:
The entire system of the small stone powder making machine is tightly sealed, which can effectively prevent dust from overflowing and reduce production noise. The production process meets the national green production standards and will not affect the external environment.
4. Wide range of applicable particle size:
The small stone powder making machine has a large feed size and a fine discharge size. The general particle size ranges from 30 mesh to 3000 mesh, and the average particle size is 6.5 microns. It is suitable for different sizes of various materials and realizes multiple uses in one machine. , Reduce the user's production cost.
How much is a small stone powder making machine?
A small stone powder making machine is usually available for tens of thousands of dollars, so what should you pay attention to when choosing a small stone powder making machine?
1. Output size: There are many models of stone powder making machines, and the output of different models is different. It is necessary to choose the output size suitable for the production site, and the price is different for different output.
2. Energy saving and environmental protection: Whether the equipment is energy saving and environmental protection is the point we need to pay attention to when purchasing equipment. At present, the country has strict environmental protection inspections, and the equipment must pass the environmental protection pass before it can be put into production.
3. Equipment quality: Quality is the issue we pay more attention to when we buy equipment. Quality is related to its operating efficiency and subsequent maintenance costs. The better the quality, the higher the work efficiency, the higher the profit generated, and the higher the equipment price.